ABB TPS48-H33 Operation Manual Download

Page: 123 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Spare parts

Page 93 / 99

HZTL4037_EN

Revision A

August 2016

Spare parts

13.1

Ordering spare parts

CAUTION

Spare part storage
All spare parts that were ordered together with the turbocharger must be

kept intact and ready for use.



Carefully clean any rusted parts and grease them.

Please quote the following data when making queries and ordering spare parts:



Turbocharger type



Serial number (HT……)



Designation and part number.

Spare parts can be ordered from any ABB Turbocharging Service Station.



If different model variants are not taken into account in this document, contact an ABB

Turbocharging Service Station.



Dispose of placed and unusable parts in an environmentally-friendly and professional

manner in accordance with the local regulations.



Dispose of the packaging of new parts in an environmentally-friendly and professional

manner in accordance with the local regulations.

13.2

Required customer spare part set (97070)

For the operations described in the Operation Manual, the customer spare part set (97070) is

required. These parts are only available in the complete set.

Part number

Designation

Quantity

42012

O-ring

52406

Gasket

72041

Counter-sunk screw

81010 / 82010

O-ring

Table 44: Required customer spare part set (97070)

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands