ABB Relion 650 Series REL650 Page 33 Commissioning Manual Download | Manualshive

Page: 33 / 176

background image

The pickup time depends on the size of the application configuration.
Application configurations with less functionality have shorter pickup
times.

If the green Ready LED continues to flash after pickup, the IED has detected an
internal error. Navigate via

Main menu/Diagnostics/IED status/General

to

investigate the error description.

3.5

Setting up communication between PCM600 and the

IED

The communication between the IED and PCM600 is independent of the
communication protocol used within the substation or to the NCC.

The communication media is always Ethernet and the used protocol is TCP/IP.

Each IED has an RJ-45 Ethernet interface connector on the front and on the rear side.
The Ethernet connector can be used for communication with PCM600.

When an Ethernet-based station protocol is used, PCM600 communication can use the
same Ethernet port and IP address.

To connect PCM600 to the IED, two basic variants must be considered.

•

Direct point-to-point link between PCM600 and the IED front port.

•

Indirect link via a station LAN or from remote via a network.

The physical connection and the IP address must be configured in both cases to enable
communication.

The communication procedures are the same in both cases.

1. If needed, set the IP address for the IEDs.
2. Set up the PC or workstation for a direct link (point-to-point), or
3. Connect the PC or workstation to the LAN/WAN network.
4. Configure the IED IP addresses in the PCM600 project for each IED to match the

IP addresses of the physical IEDs.

Setting up IP addresses

The IP address and the corresponding mask must be set via the LHMI for each
available Ethernet interface in the IED. Each Ethernet interface has a default factory IP

1MRK 506 331-UUS A

Section 3

Starting up

25

Commissioning Manual

«
...
31
32
33
34
35
...
»

Summary of Contents for Relion 650 Series REL650

















































































































































































Reviews:

No comments

Related manuals for Relion 650 Series REL650

Brand: Russound Pages: 4

Brand: Fall Guardian Pages: 3

Brand: Protekt Pages: 4

Brand: Petzl Pages: 10

BugHunter DAudio bda-4 Voice

Brand: i4Technology Pages: 6

Brand: Panasonic Pages: 99

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 26

Brand: ABB Pages: 196

Power T1+T2 1+0 275V (FM)

Brand: RST Pages: 2

Brand: Alecto Pages: 2

Brand: Leader Pages: 8

Brand: Somogyi Elektronic Pages: 9

Brand: Symantec Pages: 2

Brand: Pilz Pages: 53

PSEN op2H-A Series

Brand: Pilz Pages: 61

Brand: LEVTECH Pages: 15

Brand: LEVTECH Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands