ABB Relion 650 Series REL650 Page 12 Commissioning Manual Download

Page: 12 / 176

Checking the re-trip and back-up times........................................76
Verifying the re-trip mode.............................................................77
Verifying the back-up trip mode....................................................78
Verifying the case

RetripMode = Contact.....................................79

Verifying the function mode

Current&Contact..............................79

Completing the test.......................................................................80

Breaker failure protection, phase segregated activation and

output CSPRBRF (50BF)...................................................................80

Checking the phase current operate value, Pickup_PH...............81
Checking the residual (GF) current operate value

IN> set

below IP>......................................................................................81
Checking the re-trip and back-up times........................................81
Verifying the

RetripMode..............................................................82

Verifying the case

RetripMode = No CB Pos Check....................83

Verifying the function mode

Current&Contact..............................83

Checking the case with fault current below set value

Pickup_BlkCont............................................................................83
Checking the phase current operate value,

Pickup_PH...............84

Completing the test.......................................................................84

Stub protection STBPTOC (50STB)..................................................84

Measuring the operate limit of set values.....................................85
Completing the test.......................................................................85

Pole discrepancy protection CCRPLD (52PD)..................................86

Verifying the settings....................................................................86
Completing the test.......................................................................86

Broken conductor check BRCPTOC (46)..........................................86

Measuring the operate and time limit of set values......................87
Completing the test.......................................................................87

Directional underpower protection GUPPDUP (37)...........................87

Verifying the settings....................................................................88
Completing the test.......................................................................89

Directional overpower protection GOPPDOP (32)............................90

Verifying the settings....................................................................90
Completing the test.......................................................................91

Testing voltage protection functions.......................................................91

Two step undervoltage protection UV2PTUV (27)............................91

Verifying the setting......................................................................91
Completing the test.......................................................................92

Two step overvoltage protection OV2PTOV (59)..............................92

Verifying the settings....................................................................92

Table of contents

Commissioning Manual

Summary of Contents for Relion 650 Series REL650
















































































































































































Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands

ABB Relion 650 Series REL650, Commissioning Manual

Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands