manualshive.com logo in svg

ABB Relion 650 Series REL650, Commissioning Manual, Page: 76 / 176

Share
Download
ABB Relion 650 Series REL650 Commissioning Manual Download Page 76

For inverse time curves, check the operate time at a current equal to 110% of the
operate current for 

txMin

.

9.

Check that all trip and trip contacts operate according to the configuration (signal
matrixes)

10. Reverse the direction of the injected current and check that the step does not operate.
11. Check that the protection does not operate when the polarizing voltage is zero.
12. Repeat the above described tests for the higher set steps.
13. Finally, check that pickup and trip information is stored in the event menu.

6.4.6.2 

Four step non-directional residual overcurrent protection

1.

Do as described in 

 "Four step directional residual overcurrent protection"

, but

without applying any polarizing voltage.

6.4.6.3 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

to 

Disabled

 under 

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/

Function test modes/Current/EF4PTOC(51N67N,4IN>)/X:EF4PTOC

 for the

function, or for each individual function in a chain, to be tested next. Remember to set
the parameter 

Blocked

 to 

Yes

, for each individual function that has been tested.

6.4.7 

Sensitive directional residual overcurrent and power

protection SDEPSDE (67N)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for SDEPSDE (67N) are available on the local HMI under

Main menu/Tests/Function status/Current/SDEPSDE(67N,IN<->)/1:SDEPSDE

.

The Signal Monitoring in PCM600 shows the same signals that are available on the
local HMI.

6.4.7.1 

Measuring the operate and time limit for set values

Operation mode 3I

0

 · cosφ

Procedure

1.

Set the polarizing voltage to 1.2 · 

VNRelPU

 and the phase angle between voltage

and current to the set characteristic angle (

RCADir

), the current lagging the voltage.

Section 6

1MRK 506 331-UUS A

Testing functionality

68

Commissioning Manual

Summary of Contents for Relion 650 Series REL650

















































































































































































Reviews:

No comments