ABB Relion 650 Series REL650 Page 130 Commissioning Manual Download | Manualshive

Page: 130 / 176

background image

Should the operation not be as expected, this should be investigated. It could be
caused by an inappropriate setting or missing condition such as CBREADY (or
SYNC at three-phase reclosing).

6.

Repeat the sequence by simulating a permanent fault.
Shortly after the reclosing shot a new fault is applied. If a single-shot reclosing
program is selected, there shall be one reclosing operation and then blocking of
the auto-reclosing function for the set Reset time.
Before a new reclosing sequence can be run, the CBREADY and 52A (CB
closed) must be set manually.

6.8.3.4

Checking the reclosing conditions

When checking the influence of a releasing condition it is suggested to first run a
sequence with the condition fulfilled. When the condition signal is removed, and a new
sequence is run, it indicates that the result was due to the changed condition. In case of
a blocking signal the procedure should be similar. Start without the blocking or inhibit
signal, and then run a sequence with the blocking or inhibit signal added.

6.8.3.5

Checking the influence of the INHIBIT signal

1.

Check that the auto-reclosing function is operative, for example, by making a
reclosing shot without the INHIBIT signal.

2.

Apply a fault and thereby a PICKUP signal. At the same time, or during the open
time, apply a signal to the input INHIBIT.

3.

Check that the reclosing sequence is interrupted and no reclosing takes place.

6.8.3.6

Check closing onto a fault

1.

Check that the closing function is operative, for example by making a reclosing
shot.
Keep the CBREADY signal high.

2.

Set the breaker simulating relay BR in Open position.

3.

Close the BR relay and apply immediately a fault and thereby an INITIATE signal.

4.

Check that no reclosing takes place.

6.8.3.7

Checking the influence of CB not ready for reclosing

1.

Check that the auto-reclosing function is operative, for example by making a
reclosing shot.

Section 6

1MRK 506 331-UUS A

Testing functionality

122

Commissioning Manual

«
...
128
129
130
131
132
...
»

Summary of Contents for Relion 650 Series REL650

















































































































































































Reviews:

No comments

Related manuals for Relion 650 Series REL650

3M Full Body Harnesses

Brand: AC Tool Supply Pages: 17

Brand: Gardigo Pages: 24

Brand: Krantz Pages: 36

Brand: Siemens Pages: 12

Brand: Siemens Pages: 13

SIPROTEC 5 7UM85

Brand: Siemens Pages: 92

Brand: Siemens Pages: 134

Siprotec 7SD600

Brand: Siemens Pages: 174

Brand: Siemens Pages: 210

Brand: Siemens Pages: 260

Brand: Siemens Pages: 325

SIPROTEC 4 7VK61

Brand: Siemens Pages: 360

Brand: Siemens Pages: 416

SIPROTEC 7SD610

Brand: Siemens Pages: 448

Brand: Siemens Pages: 602

Brand: Siemens Pages: 604

siprotec 7SA522

Brand: Siemens Pages: 628

SIPROTEC 7UT613 series

Brand: Siemens Pages: 638

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands