ABB Relion 650 Series REL650 Page 102 Commissioning Manual Download

Page: 102 / 176

6.5.4.1

Measuring the operate limit of set values

Check that the input logical signals BLOCK, CBOPEN and BLKU are logical zero.

Supply a three-phase rated voltage in all three phases and note on the local HMI
that the TRIP logical signal is equal to the logical 0.

Switch off the voltage in all three phases.
After set

tTrip

time a TRIP signal appears on the corresponding binary output or

on the local HMI.

Note that TRIP at this time is a pulse signal, duration should be
according to set

tPulse

Inject the measured voltages at rated values for at least set

tRestore

time.

Activate the CBOPEN binary input.

Simultaneously disconnect all the three-phase voltages from the IED.
No TRIP signal should appear.

Inject the measured voltages at rated values for at least set

tRestore

time.

Activate the BLKU binary input.

Simultaneously disconnect all the three-phase voltages from the IED.
No TRIP signal should appear.

10. Reset the BLKU binary input.
11. Inject the measured voltages at rated values for at least set

tRestore

time.

12. Activate the BLOCK binary input.
13. Simultaneously disconnect all the three-phase voltages from the IED.

No TRIP signal should appear.

14. Reset the BLOCK binary input.

6.5.4.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Voltage/LOVPTUV(27,U<)/1:LOVPTUV

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

Yes

, for each individual function that has been tested.

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Summary of Contents for Relion 650 Series REL650
















































































































































































Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands

ABB Relion 650 Series REL650, Commissioning Manual

Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands