ABB Relion 650 Series REL650 Page 104 Commissioning Manual Download

Page: 104 / 176

Slowly decrease the frequency of the applied voltage, to a value below

PUFrequency

Check that the PICKUP signal does not appear.

Wait for a time corresponding to

tDelay

, and check that the TRIP signal does not

appear.

6.6.1.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Frequency/SAPTUF(81,f<)/X:SAPTUF

for the function, or for

each individual function in a chain, to be tested next. Remember to set the parameter

Blocked

Yes

, for each individual function that has been tested.

6.6.2

Overfrequency protection SAPTOF (81)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for SAPTOF (81) are available on the local HMI under

Main menu/Tests/Function status/Frequency/SAPTOF(81,f>)/X:SAPTOF

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.6.2.1

Verifying the settings

Verification of PICKUP value and time delay to operate

Check that the settings in the IED are appropriate, especially the PICKUP value
and the definite time delay.

Supply the IED with three-phase voltages at their rated values.

Slowly increase the frequency of the applied voltage, until the PICKUP signal
appears.

Note the operate value and compare it with the set value.

Decrease the frequency to rated operating conditions.

Check that the PICKUP signal resets.

Instantaneously increase the frequency of the applied voltage to a value about
20% higher than the operate value.

Measure the time delay for the TRIP signal, and compare it with the set value.

Extended testing

The test above can be repeated to check the time to reset.

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Summary of Contents for Relion 650 Series REL650
















































































































































































Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands

ABB Relion 650 Series REL650, Commissioning Manual

Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands