ABB Relion 650 Series REL650 Page 94 Commissioning Manual Download

Page: 94 / 176

6.4.12

Pole discrepancy protection CCRPLD (52PD)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for CCRPLD (52PD) are available on the local HMI
under

Main menu/Tests/Function status/Current/CCRPLD(52PD)/X:CCRPLD

The Signal Monitoring in PCM600 shows the same signals that are available on the
local HMI.

6.4.12.1

Verifying the settings

When CCRPLD (52PD) is set for external, set setting

ContSel

Enable

under

Main menu/Settings/IED Settings/Current/CCRPLD/1:CCRPLD

to activate

the logic that detects pole discordance when external pole discordance signaling
is used (input EXTPDIND) in the application configuration.

Activate the input EXTPDIND on CCRPLD (52PD) function block, and measure
the operating time of CCRPLD (52PD).

Compare the measured time with the set value

tTrip

Reset the EXTPDIND input.

When CCRPLD (52PD) is set for unsymmetrical current detection with CB
monitoring, set setting

CurrSel

under

Main menu/Settings/IED Settings/

Current/CCRPLD/1:CCRPLD

Enable

Use the TRIP signal from the configured binary output to stop the timer.

Repeat point 4 and 5 using OPENCMD instead of CLOSECMD. Set all three
currents to 110% of

CurrRelLevel

. Activate CLOSECMD.

NO TRIP signal should appear due to symmetrical condition.

6.4.12.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Current/CCRPLD(52PD)/X:CCRPLD

for the function, or for

each individual function in a chain, to be tested next. Remember to set the parameter

Blocked

Yes

, for each individual function that has been tested.

6.4.13

Broken conductor check BRCPTOC (46)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Summary of Contents for Relion 650 Series REL650
















































































































































































Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands

ABB Relion 650 Series REL650, Commissioning Manual

Search results

Summary of Contents for Relion 650 Series REL650

Reviews:

Related manuals for Relion 650 Series REL650

Brands by name

Popular brands