ABB IRB 140 Product Manual Download Page 211

Page: 211 / 252

Note

Action

Place the gearbox unit with the lower arm
side downwards on a suitable workbench.

Clean the mating surfaces of the base and
of the gearbox unit with isopropanol.

Shown in the figure

Illustration, base on

page 208

Fit a small amount of Loctite 574 on the
mating surface in the gearbox unit.

Shown in the figure

Illustration, base on

page 208

Fit the base to the gearbox unit and secure
it with the

attachment screws

and the

washer.

20 pcs, tightening torque: 35 Nm ± 3 Nm.

Shown in the figure

Location of gearbox

unit, axes 1-2 on page 207

Refit the

bottom plate

and secure it with its

attachment screws

Fit the

lifting slings

to the base/gearbox unit,

turn it right side up and move it to the install-
ation site.

Attachment bolts and the tightening
torque are specified in section

Attachment

screws on page 62

Secure the base to the foundation

Detailed in section

Replacement of com-

plete lower arm on page 134

Refit the lower arm.

Detailed in section

Replacement of com-

plete upper arm on page 128

Refit the upper arm.

Detailed in section

Replacing the serial

measurement unit and the battery pack
on page 167

Refit the serial measurement board.

Detailed in section

Replacement of cable

harness on page 120

Refit the cable harness.

Detailed in sections:

•

Replacement of motor, axis 1 on
page 177

•

Refitting, motor axis 2 on page 184

Refit the motors, axes 1 and 2.

Detailed in section

Performing a leak-

down test on page 241

Perform a leak-down test.

See,

Technical reference manual - Lubric-

ation in gearboxes

Fill the two gearboxes with oil.

Seal and paint the joints that have been
opened. See

Cut the paint or surface on the

robot before replacing parts on page 118

Note

After all repair work, wipe the robot free
from particles with spirit on a lint free cloth.

Pendulum Calibration is described in

Op-

erating manual - Calibration Pendulum

enclosed with the calibration tools.

Recalibrate the robot.

General calibration information is included
in section

Calibration information on

page 215

Continues on next page

Product manual - IRB 140

211

3HAC027400-001 Revision: V

4 Repair

4.8.1 Replacement of gearbox, axes 1-2 and damper, axis 1

Continued

Summary of Contents for IRB 140





























































































































































































































































Search results

Summary of Contents for IRB 140

Reviews:

Brands by name

Popular brands

ABB IRB 140, Product Manual

Search results

Summary of Contents for IRB 140

Reviews:

Brands by name

Popular brands