ABB GOE(2) Installation And Commissioning Manual Download | Manualshive

Page: 10 / 80

background image

10

Installation and commissioning guide

1ZSC000563-ACF EN, REV. A, 2020-06-25

Test tap

The bushing has a test tap that is connected to the outermost conductive layer of the condenser core. The test
tap is used to measure the bushing insulation by capacitance and dissipation factor. The cover connects the
outermost conductive layer to ground, and must always be installed when the bushing is energized.

The maximum one minute test voltage for this test tap is 20 kV

rms

. The test tap can be used as a power

source, if it is connected to an external capacitance. The operating voltage is limited to 6 kV.

CAUTION!

Do not energize the bushing without a test adapter or the cover installed. The bushing is grounded
through the cover to prevent damage to the bushing.

G002993

3

O-ring

9

Oil plug for oil-filling if the test tap is used as power source.

57 Stud

58 Cover

59 Grounding spring

Test adapter, 2769 522-C, optional equipment

The test adapter 2769 522-C is available for permanent connection to measuring circuits. Please refer to Test
adapter – Technical guide 1ZSC000563-ACS and Installation and maintenance guide 1ZSC000563-ACD.

G003049

«
...
8
9
10
11
12
...
»

Summary of Contents for GOE(2)

















































































Reviews:

No comments

Related manuals for GOE(2)

Brand: Bacharach Pages: 2

Brand: WDS Pages: 32

Brand: Icom Pages: 3

Brand: Icom Pages: 40

PULSAR RADAR R86

Brand: Magnetrol Pages: 16

Brand: KLAY-INSTRUMENTS Pages: 5

Brand: Yaesu Pages: 60

Brand: RKI Instruments Pages: 45

Brand: Sony Pages: 2

Brand: UTEPO Pages: 2

Brand: Bellman & Symfon Pages: 3

Brand: Bellman & Symfon Pages: 56

Brand: Bellman & Symfon Pages: 66

Gemco Brik 955QD Series

Brand: Ametek Pages: 24

Brand: Icom Pages: 32

Brand: Icom Pages: 110

Brand: HYDAC ELECTRONIC Pages: 40

Brand: Minebea Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands