manualshive.com logo in svg

ABB GOE(2), Installation And Commissioning Manual

Share
Download
ABB GOE(2) Installation And Commissioning Manual Download Page 45

Installation and commissioning guide
1ZSC000563-ACF EN, REV. A, 2020-06-25

45

4.8 Manual tightening of the draw-rod nut

Overview

This procedure requires the draw-rod nut and threads of the draw rod to be correctly lubricated. The draw rod
will not get the correct tension if the fasteners are not correctly lubricated, this can cause the bushing to fail.
If possible, ABB recommends that the draw rod is hydraulically tightened, refer to

Hydraulic tightening of

the draw-rod nut,

page

42

.

Procedure

1.

Make sure that the draw-rod nut, and threads of the draw rod are correctly lubricaded, and that the
draw-rod nut is tightened to 10 Nm.

2.

Measure the distance (a).

G006845

3.

Turn the nut clockwise until you get the correct
extension (b).

Distance (b) = (a) + extension, refer to the table.

CAUTION!

Make sure that you do not overtighten
the nut. Use a torque wrench set to
140 Nm.

NOTE!

One turn of the nut corresponds to a
2 mm extension of the draw rod.

Type

Extension

GOE(2) 1175

8.5 mm ±1.0

GOE(2) 1425

9.5 mm ±1.0

GOE(2) 1550

10.5 mm ±1.0

GOE(2) 1675

10.5 mm ±1.0

G006846

4.

Make sure with a torque wrench that the nut is tightened with a torque of more than 70 Nm and less
than 140 Nm.

End of instruction

Summary of Contents for GOE(2)

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands