manualshive.com logo in svg

ABB FCAN-01, User Manual

Share
Download
ABB FCAN-01 User Manual Download Page 119

Communication protocol   119

Tx PDO21

Note:

 The mapping entries of the Tx PDO21 can be configured 

through CANopen object 1A14h or from the drive with fieldbus 

configuration parameter group C (group 3).
The default COB ID for Tx PDO21 is 800 Node ID (Tx 

PDO21 disabled), the default transmission type is 255 and the 

event time is 0. These values can be changed with CANopen 

object 1614h or from the drive with parameters 22, 23 and 24 of 

the fieldbus configuration group A (group 1).

Mapped 

obj 1

Mapped 

obj 2

Mapped 

obj 3

Mapped 

obj 4

Byte

1

2

3

4

5

6

7

8

CANopen object for 

mapping

1A14h01

1A14h02

1A14h03

1A14h04

Mapping 

parameter

1)

ACS355

FBA DATA 
IN 7

FBA DATA 
IN 8

FBA DATA 
IN 9

FBA DATA 
IN 10

ACSM1

ACS850
ACS880

FBA DATA 
IN 9

FBA DATA 
IN 10

FBA DATA 
IN 11

FBA DATA 
IN 12

1)

 Configuration group C (group 3) (when parameter 04 CONF LOC = 1)

Summary of Contents for FCAN-01

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands