ABB FBVi-2U4-4T User Manual Download Page 86

Page: 86 / 102

FBVi-2U4-4T |

Control Sequence

Subject to change without notice

WWW.CYLON.COM

v 5

CO₂ AND HUMIDITY

₂

CONTROL

CO₂

sensor should be wired to UI4, and

UI4Config (A174)

is set to 0.

This will take a voltage signal from 0-10V.
To adjust the

CO₂

reading dependent on altitude above sea level, enter the height in ft into the

altitude

(A215)

analog setpoint.

•

On a rise in zone

CO₂

levels above the

CO2_Stpt (A223),

the VAV box flow will reset upwards to the

maximum flow setpoint.

•

To disable the

CO₂

flow reset based on CO2, set

enableCO2_DCV (D270)

FALSE

. This may be

necessary on cooling only boxes with no supplemental heat.

The minimum

CO₂

range in ppm is set using

minCO2Range (A278),

and the maximum

CO₂

range is set

using

maxCO2Range (A280)

analog setpoint.

HUMIDITY MONITORING

Humidity will be monitored by the CBT-Stat or if

UI4Config (A174)

is set to 1 and a 0-10v humidity

sensor is wired.

WINDOW SENSOR AND FAN STATUS

WINDOW SENSOR

If an input has been configured for a window sensor, the input is N.O. when the window state is closed.

When a window has been opened, the input will close. The status is read at

windowOpen (D251).

When a window has been detected open:

•

Heating and cooling are disabled.

•

Damper is closed.

•

Any VAV fans are disabled.

FAN STATUS

If UI 4 has been configured for fan status, the input is N.O. when the fan is off. When the fan is energized,

the input will close. The

fanConfig (A54)

analog setpoint

should be set for either parallel or series fan

control. The status is read at

fanStatus (D88).

•

If the series or parallel fan has been commanded ON and no fan status has been detected within 30

seconds, a fan alarm will be generated.

DAMPER CONTROL

The

FBVI-2U4-4T

controller provides pressure-independent zone temperature control by calculating

airflow rate setpoints based on the space temperature deviation from zone setpoint and the duration of

deviation. The primary inlet airflow rate is measured and compared to this control point. Any error

greater than the deadband setting will cause the primary air damper to be driven open or closed as

required to reduce the error to within an adjustable Flowrate deadband.

The primary airflow setpoint is read from point

activeFlowSetpoint (A236).

Specific details on airflow and airflow setpoints can be reviewed in Section 3 Control sequences.

Summary of Contents for FBVi-2U4-4T







































































































Search results

Summary of Contents for FBVi-2U4-4T

Reviews:

Related manuals for FBVi-2U4-4T

Brands by name

Popular brands

ABB FBVi-2U4-4T, User Manual

Search results

Summary of Contents for FBVi-2U4-4T

Reviews:

Related manuals for FBVi-2U4-4T

Brands by name

Popular brands