ABB Conceptpower DPA 500 Operating Manual Download Page 39

Page: 39 / 114

Modifications reserved

Page 39/94

Mains on X1

JP2

JP3

JP4

480V

OFF

230V

OFF

120V

6.2.4

Multidrop Configuration

Multidrop cable connection

Insert the splitter/s supplied with the installation inside the Multidrop connector/s
JR2 on NW22085 on all middle unit/s.

Connect the “Previous” end of the multidrop cable on the First Unit and the

“Next” end on the second Unit (If more than two unit inside the splitter).

Proceed on the same way with all other unit on the installation as shown on the
picture.

Board NW22085 Jumper & Switches configuration
Verify that the customer interface board (

NW22085)

of each unit correctly configured according to the

following table

JUMPER JP 2

on PCB NW22085

(with ROM76-12) or

NW22085

or later versions

First unit

OFF

Middle Unit

Last Unit

Note: on the (older) versions NW22085B/C without ROM76-12 make a bridge between X3-11 & X3-12.

6.2.5

ON/OFF – Main Buttons

The ON/OFF-Buttons serve to shutdown the UPS-system for service or maintenance or for

emergency reasons.

NOTE

WHEN BOTH ON/OFF BUTTONS ON ALL UPS MODULES IN A PARALLEL
SYSTEM ARE PUSHED THE POWER SUPPLY TO THE LOAD WILL BE

INTERRUPTED

Prev

Next

Prev

Next

First Unit

Middle Unit

Last Unit

Summary of Contents for Conceptpower DPA 500














































































































Search results

Summary of Contents for Conceptpower DPA 500

Reviews:

Related manuals for Conceptpower DPA 500

Brands by name

Popular brands

ABB Conceptpower DPA 500, Operating Manual

Search results

Summary of Contents for Conceptpower DPA 500

Reviews:

Related manuals for Conceptpower DPA 500

Brands by name

Popular brands