manualshive.com logo in svg

ABB CONCEPTPOWER CLASSIC DPA-50, User Manual

Share
Download
ABB CONCEPTPOWER CLASSIC DPA-50 User Manual Download Page 62

 
 
 
 
 
 

Section-5

 

 

 

04-3008_S5_ABB_OPMCPDPA-S2_GB_121202

 

Page 2/16   ABB 

Printed in Switzerland – Modifications reserved

 

5.1 

OPERATION - PROCEDURES 

5.1.1 Start-Up 

Procedure 

 

WARNING

!

 

THE OPERATIONS DESCRIBED IN THIS CHAPTER MUST BE 
PERFORMED BY A SERVICE ENGINEER FROM THE MANUFACTURER OR 
FROM A AGENT AUTHORIZED BY THE MANUFACTURER. 

 

Situation of UPS-System before switching it on: 

1. 

Make sure the fuses for the supply of UPS-System in the Input Distribution Board on site are open. 

2. 

Make sure all the input and output cabling has been performed correctly and check the input phase 
rotation. 

3. 

Verify that all Parallel Isolator Switches IA2-1, IA2-2, IA2-3, IA2-4, IA2-5 (depending of the UPS 
frames) are open (Position OFF). 

4. 

Verify that the Maintenance Switch IA1 is open and in Position OFF. 

5. 

Make sure all the internal battery fuses in the UPS (if any) and the external battery cabinets are open. 

6. 

Check the Position of the DIP Switches SW1-9. This is a 

Single-

 

Cabinet

 Configuration, and the  DIP 

Switches SW1-9 must be set according to positions shown in section 4 Table of Paragraph 1.2.6 

Start up procedure of Conceptpower DPA

TM

: 

1. 

Insert fuses for the supply of UPS-System in the Input Distribution 
- The LED-indicators LINE 1 and battery on UPS-Module is lit – green 
- On LCD-Display “LOAD OFF, SUPPLY FAILURE” will appear.

 

2. UPS-Module 

1: 

Press both “ON/OFF” Main Buttons to switch on UPS. 
LCD panel must display: “LOAD DISCONNECTED PARALLEL SWITCH OPEN” and the LED-
indicator will appear as shown below:

 

LED Indicator 

Colour 

LINE 1 

Green 

LINE 2 

Green 

BYPASS Green 

INVERTER OFF 

BATTERY Flashing 

Green 

3. 

Check Command: LOAD TO INVERTER 
LED indicator will appear as shown below: 

Summary of Contents for CONCEPTPOWER CLASSIC DPA-50


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands