Installation
73
Note 6:
Alternative installation means
In addition to the installation examples presented in this chapter, there are a few
alternative installation means, such as:
• The power cables can be connected directly to the drive module input and output
terminals with cable lugs or by busbars. The drive module can also be installed
self standing to the floor in an electrical equipment room when the power cable
terminals and electrical parts are protected against contact and the unit is
grounded properly.
• The drive module without pedestal (0H354) can be mounted on wall or
cabinet with four screws through the fastening holes at the top and bottom of the
right-hand side of the module.
Safety
WARNING!
Only qualified electricians are allowed to carry out the electrical
installation work described in this chapter. Follow the
on the first
pages of this manual. Ignoring the safety instructions can cause injury or death.
Checking the installation site
The material below the drive must be non-flammable and strong enough to carry the
weight of the drive.
for the allowed ambient conditions and
Losses, cooling data and noise
on page
for the required cooling air.
Required tools
• Set of screw drivers (Torx and Pozidrive)
• Torque wrench with a 500 mm (20 in.) or 2 × 250 mm (2 × 10 in.) long extension
bar
• 17 mm (11/16 in.) magnetic-end socket for mounting the drive module busbars to
the optional cabling panels (+H381 or +H383)
• 10 mm magnetic-end socket or a torx screw driver for mounting the drive module
top fastening bracket to the cabinet back and for mounting the optional cabling
panels (+H381 or +H383) to the cabinet side panels
• 13 mm socket for mounting the drive module to the cabinet bottom plate or floor
• 22 mm magnetic-end socket for mounting the cable lugs to the terminals (M12
bolt).
Summary of Contents for ACS850-04 series
