Technical data
102
Symbols
Note:
The ratings apply in ambient temperature of 40 °C (104 °F). In lower temperatures the ratings are
higher.
Input cable fuses
The recommended fuses are for branch circuit protection per NEC.
Check that the
operating time of the fuse is below 0.5 seconds and the fuses are of the “non-
time delay” type .
The operating time depends on the fuse type (T/L or aR), supply
network impedance and the cross-sectional area, material and length of the supply
cable. In case the 0.5 seconds operating time is exceeded with T/L fuses, ultrarapid
(aR) fuses will in most cases reduce the operating time to an acceptable level. The
fuses must be of the “non-time delay” type. See also
Thermal overload and short-circuit protection
Note 1: In multicable installations, install only one fuse per phase (not one fuse per conductor).
Note 2:
Larger fuses must not be used.
Note 3:
Fuses from other manufacturers can be used if they meet the ratings.
I
max
maximum output current. Available for 10 s ar start, otherwise as long as allowed by drive
temperature.
Normal use
(10 % overload capability)
I
2N
continuous rms current. 10 % overload is typically allowed for one minute every 5 minutes.
P
N
typical motor power. The power ratings apply to most 4-pole NEMA rated motors (230 V or
460 V).
Heavy-duty use
(50 % overload capability)
I
2hd
continuous rms current. 50 % overload is typically allowed for one minute every 5 minutes.
P
hd
typical motor power. The power ratings apply to most 4-pole NEMA rated motors (230 V or
460 V).
ACS800-U2 type
Input
current
Fuse
A
A
V
Manufacturer
Type
UL class
Three-phase supply voltage 208 V, 220 V,
230 V
or 240 V
-0080-2
201
250
600
Bussmann
JJS-250
T
-0100-2
239
300
600
Bussmann
JJS-300
T
-0120-2
285
400
600
Bussmann
JJS-400
T
-0140-2
391
500
600
Bussmann
JJS-500
T
-0170-2
428
600
600
Bussmann
JJS-600
T
-0210-2
506
600
600
Bussmann
JJS-600
T
-0230-2
599
800
600
Bussmann
KTU-800
1)
L
-0260-2
677
800
600
Bussmann
KTU-800
1)
L
-0300-2
707
800
600
Bussmann
KTU-800
2)
L
Summary of Contents for ACS800-02
