Chapter 8 – Parameters
ACA 635 IGBT Supply Sections
8-21
70.05
CH0 COMM LOSS
CTRL
I
FAULT
This parameter is in use when Par. 98.01
COMMAND SEL is set to MCW and Par.
98.02 COMM MODULE to FBA DSET1,
FBA DSET10 or INVERTER.
(1)
NO FAULT
A warning is given on communication loss
on channel CH0.
(2)
FAULT
Converter trips on communication loss on
channel CH0.
70.06
CH1 LINK
CONTROL
R
10
1...15
DDCS channel CH1 intensity control for
transmission LEDs. This value is adjusted
through the link including each device in
the link. This parameter can be used in
special cases to optimise the
communication performance in the link.
1 = 1
70.15
CH3 NODE ADDR
R
1
1...254
Node address for the channel CH3. This
channel is normally used with the start-up
and maintenance tools. If CH3 of the
several drives have been connected to
the ring or star (by branching unit)
connection, each one must be set an
unique node address. The new node
address becomes valid only after auxiliary
power shutdown of the NAMC board.
1 = 1
70.16
CH3 LINK
CONTROL
R
15
1...15
DDCS channel CH3 intensity control for
transmission LEDs. This value is adjusted
through the link including each device in
the link. This parameter can be used in
special cases to optimise the
communication performance in the link.
1=1
70.19
CH0 HW
CONNECTION
B
STAR
This parameter is used for enabling or
disabling regeneration of channel CH0
optical transmitter in DDCS mode. DDCS
mode is typically used with APC2, AC70
and AC450 controllers. In regeneration
mode any message received by the
channel is echoed back. This parameter is
not in use in DriveBus mode.
1=1
(0)
RING
Regeneration enabled. Select RING if the
CH0 channels on the NAMC boards are
connected to a ring configuration.
(1)
STAR
Regeneration disabled. Select STAR with
a star configuration as AC450 – CI810 –
NDBU-95 optical branching unit(s) –
ACS 600.
70.20
CH3 HW
CONNECTION
B
STAR
This parameter is used for enabling or
disabling regeneration of channel CH3
optical transmitter. In regeneration mode
any message received by the channel is
echoed back.
1=1
(0)
RING
Regeneration enabled. Select RING if the
CH3 channels on the NAMC boards are
connected to a ring configuration.
(1)
STAR
Regeneration disabled. Select STAR with
a star configuration as Drive
Window
(PC)
– NDBU-95 optical branching unit(s) –
ACS 600.
Summary of Contents for ACS 600 MultiDrive
