![background image](http://html.mh-extra.com/html/abb/ach480/ach480_hardware-manual_2507078.webp)
Connection examples of two-wire and three-wire sensors
The figures give examples of connections for a two-wire or three-wire sensor/transmitter
that is supplied by the auxiliary voltage output of the drive.
P
I
-
+
4…20 mA AI2
AGND
+24V
DGND
Process actual value measurement or reference, 0(4) … 20 mA, Rin = 137 ohm. If the
sensor power supply comes through its current output circuit, use 4 … 20 mA signal,
not 0 … 20 mA.
AI2
AGND
Auxiliary voltage output, non-isolated, +24 V DC, max. 250 mA
+24V
DGND
P
I
-
+
OUT (0)4…20 mA AI2
AGND
+24V
DGND
Process actual value measurement or reference, 0(4)…20 mA, Rin = 137 ohm
AI2
AGND
Auxiliary voltage output, non-isolated, +24 V DC, max. 250 mA
+24V
DGND
AI and AO (or AI, DI and +10 V) as PTC motor temperature sensor interface
WARNING!
IEC 60664 and IEC 61800-5-1 require double or reinforced insulation between
live parts and accessible parts when:
•
the accessible parts are not conductive, or
•
the accessible parts are conductive, but not connected to the protective earth.
Obey this requirement when you plan the connection of the motor temperature
sensor to the drive.
If the motor temperature sensor has a reinforced insulation vs. the motor windings, you
can connect it directly to the drive IO interface. This section shows two connection
alternatives for the direct I/O connection. If the sensor does not have reinforced insulation,
you must use another type of connection to fulfill the safety requirements. See
Implementing a motor temperature sensor connection (page 56)
.
78 Electrical installation – IEC
Summary of Contents for ACH480
