![background image](http://html.mh-extra.com/html/abb/ach480/ach480_hardware-manual_2507146.webp)
Connector pitch 5 mm, wire size 2.5 mm2 (14 AWG)
EIA-485 embedded
fieldbus (A+, B-,
DGND)
Physical layer: RS-485
Cable type: Shielded twisted pair cable with twisted pair for data and a
wire or pair for signal ground, nominal impedance 100 … 165 ohm, for
example Belden 9842
Transmission rate: 9.6 … 115.2 kbit/s
Termination by switch
Efficiency
Approximately 98% at nominal power level.
Protection classes
IP20. The drive must be installed in a cabinet to fulfill the requirements
for shielding from contact.
Degree of protection
(IEC/EN 60529)
UL open type. For indoor use only. UL Type 1 kit is available as an option.
Enclosure types
(UL 61800-5-1)
lll
Overvoltage category
(IEC 60664-1)
l
Protective classes
(IEC/EN 61800-5-1)
Ambient conditions
Environmental limits for the drive are given below. The drive must be used in a heated
indoor controlled environment.
Transportation in the
protective package
Storage in the protect-
ive package
Operation installed
for stationary use
Requirement
-
-
400/480 V drives
:
0 … 4000 m
(0 … 13123 ft) above
sea level (with output
derating above 1000 m
[3281 ft])
Installation site alti-
tude
See
-40 … +70 °C ±2%
-40 … +70 °C ±2%
-10 … +60 °C
(14 … 140 °F).
Surrounding air tem-
perature
(-40 … +158 °F ±2%)
(-40 … +158 °F ±2%)
If the temperature is
more than 50 °C
(122 °F), output derat-
ing is necessary. See
No frost permitted.
146 Technical data
Summary of Contents for ACH480
