![background image](http://html.mh-extra.com/html/abb/ach480/ach480_hardware-manual_2507016.webp)
General safety in installation, start-up and maintenance
These instructions are for all personnel who do work on the drive.
WARNING!
Obey these instructions. If you ignore them, injury or death, or damage to the
equipment can occur.
•
Keep the drive in its package until you install it. After unpacking, protect the drive
from dust, debris and moisture.
•
Use the required personal protective equipment: safety shoes with metal toe cap,
safety glasses, protective gloves and long sleeves, etc. Some parts have sharp
edges.
•
Beware of hot surfaces. Some parts, such as heatsinks of power semiconductors,
and brake resistors, remain hot for a while after disconnection of the electrical supply.
•
Vacuum clean the area around the drive before the start-up to prevent the drive
cooling fan from drawing the dust inside the drive.
•
Make sure that debris from drilling, cutting and grinding does not enter the drive
during the installation. Electrically conductive debris inside the drive may cause
damage or malfunction.
•
Make sure that there is sufficient cooling. See the technical data.
•
Before you connect voltage to the drive, make sure that all covers are in place. Do
not remove the covers when voltage is connected.
•
Before you adjust the drive operation limits, make sure that the motor and all driven
equipment can operate throughout the set operation limits.
•
Before you activate the automatic fault reset or automatic restart functions of the
drive control program, make sure that no dangerous situations can occur. These
functions reset the drive automatically and continue operation after a fault or supply
break. If these functions are activated, the installation must be clearly marked as
defined in IEC/EN 61800-5-1, subclause 6.5.3, for example, "THIS MACHINE
STARTS AUTOMATICALLY".
•
The maximum drive power cycles is five times in ten minutes. Power cycling the
drive too often can damage the charging circuit of the DC capacitors.
•
If you have connected safety circuits to the drive (for example, Safe torque off or
emergency stop), validate them at start-up. See separate instructions for the safety
circuits.
•
Beware of hot air exiting from the air outlets.
•
Do not cover the air inlet or outlet when the drive is running.
16 Safety instructions
3
Summary of Contents for ACH480
