A-TS TECHNOLOGY Pulse Series User Manual Download

Page: 25 / 67

www.a-ts.cn A-TS Technology RT10

CLK-

Serial clock (When it is the Nikon/ Biss /

Endat encoder)

CLK+

Shield ground, it is connected to the metal

shield layer of shield wire.

2.2.5 USB debugging port X3 definition

This terminal is the USB3.0A plug, compatible with USB2.0. But

it’s

different from the standard USB3.0 definition. This port is mainly used for

the upper machine software communication debugging, and MCU firmware

updating.

Doing the MCU firmware updating, it uses the USB communication, by

the standard USB2.0 cable.

When communicating with upper machine, the serial communication is

used. The communication cable is an optional accessory, and is the

standard USB3.0 cable specially made. Only the 5 /6 / 7 pins need to be

welded as below.

Figure 2-7 USB3.0 A type USB plug (left) and socket (right)

USB3.0 pins as follows

Pin No.

Signal name

Description

D5V

USB positive pole (optional)

USB_D-

USB data-

Summary of Contents for Pulse Series




































































Search results

Summary of Contents for Pulse Series

Reviews:

Related manuals for Pulse Series

Brands by name

Popular brands

A-TS TECHNOLOGY Pulse Series, User Manual

Search results

Summary of Contents for Pulse Series

Reviews:

Related manuals for Pulse Series

Brands by name

Popular brands