A.O. Smith SGS - 100 Page 107 Installation, User And Service Manual Download

Page: 107 / 121

Performing maintenance

104

Instruction manual SGS

6. Fit the chimney flue.

Note

Check the pressure differential again after cleaning. If the pressure

differential is too low following cleaning, please contact the supplier of the water
heater.

15.5 Solar collector

maintenance

See installation or users' manual for the solar collector. If this topic is not
covered in the manual, then contact the supplier of the collectors.

15.6 Finalizing

maintenance

See Eratta.

1. Fill the water heater (5 "Filling").
2. Start the water heater (9 "Starting the water heater")
3. Check the CO

value (3.13.3 "CO

adjustment").

4. Check the switching pressure of the pressure switch. (3.13.4 "Switching

pressure measurement")

5. Erase the message

SERVICE REQUIRED

. Do this by pressing once on

then once on

Summary of Contents for SGS - 100


























































































































Search results

Summary of Contents for SGS - 100

Reviews:

Related manuals for SGS - 100

Brands by name

Popular brands

A.O. Smith SGS - 100, Installation, User And Service Manual

Search results

Summary of Contents for SGS - 100

Reviews:

Related manuals for SGS - 100

Brands by name

Popular brands