3Jtech G2Wifi II Page 19 User Manual Download

Page: 19 / 87

http://www.3jtech.com.tw

http://www.pnpipcameras.com

G2wifi II User’s Manual

Use Unicasting:

This option is normally turned off, and should remain off as long as the

WAN-side DHCP server correctly provides an IP address to the router. However, if the router

cannot obtain an IP address from the DHCP server, the DHCP server may be one that works

better with unicast responses. In this case, turn the unicasting option on, and observe whether

the router can obtain an IP address. In this mode, the router accepts unicast responses from

the DHCP server instead of broadcast responses.

Enable BigPond:

Check this option to connect to the Internet through Telstra BigPond Cable

Broadband in Australia. Telstra BigPond provides the values for

BigPond Server

BigPond

User Id

, and

BigPond Password

Summary of Contents for G2Wifi II
























































































Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands

3Jtech G2Wifi II, User Manual

Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands