3Jtech G2Wifi II Page 77 User Manual Download

Page: 77 / 87

http://www.3jtech.com.tw

http://www.pnpipcameras.com

G2wifi II User’s Manual

4.1.5 Network

In Network you can check the Network status, configure the WAN Settings, LAN Settings and DDNS

Settings.

Network Status:

You can check the current network setting in this page.

WAN Settings:

In this page you can configure the IP Phone WAN port’s setting. The WAN port is for

you to connect to the ADSL Router and Broadband Router.

The IP Phone’s default setting is NAT mode. If you do not need to use the NAT Mode, you can

change to Bridge Mode. If you change the setting to Bridge Mode, then the LAN setting will not effect

and will be the same as WAN port. The WAN port default is DHCP Client mode, you can change the

setting to Fixed IP Mode.

If you change the WAN port’s setting to Fixed IP Mode, then you have to make sure the IP address,

Net Mask, Gateway, and DNS settings are suitable for your current network environment.

When you finished the setting, please click the

Submit

button. If there is nothing need to change,

please click the

Save Change

item in the left side, then click the

Save

button. The change you made

will save into the system and the system will reboot automatically.

Summary of Contents for G2Wifi II
























































































Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands

3Jtech G2Wifi II, User Manual

Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands