manualshive.com logo in svg

3Jtech G2Wifi II, User Manual

Share
Download
3Jtech G2Wifi II User Manual Download Page 35

http://www.3jtech.com.tw

 

http://www.pnpipcameras.com

   

G2wifi II User’s Manual   

Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.) 

35 

 

RADIUS Server IP Address: 

The IP address of the authentication server.   

 

RADIUS Server Port: 

The port number used to connect to the authentication server. 

   

RADIUS Server Shared Secret: 

A pass-phrase that must match with the authentication 

server.  

 

MAC Address Authentication: 

If this is selected, the user must connect from the same 

computer whenever logging into the wireless network.   

 

Advanced >>:   

 

Optional Backup RADIUS Server: 

This option enables configuration of an optional 

second RADIUS server. A second RADIUS server can be used as backup for the primary 

RADIUS server. The second RADIUS server is consulted only when the primary server is 

not available or not responding. The fields 

Second RADIUS Server IP Address

, 

Second

 

RADIUS Server Port

, 

Second RADIUS server Shared Secret

, 

Second MAC Address 

Authentication

 provide the corresponding parameters for the second RADIUS Server.   

Summary of Contents for G2Wifi II
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands