manualshive.com logo in svg

3Jtech G2Wifi II, User Manual

Share
Download
3Jtech G2Wifi II User Manual Download Page 66

http://www.3jtech.com.tw

 

http://www.pnpipcameras.com

   

G2wifi II User’s Manual   

Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.) 

66 

 

3.4.5 Statistics 

The Statistics page displays all of the LAN and WAN packet transmit and receive statistics. 

 

Sent: 

The number of packets sent from the router. 

 

Received: 

The number of packets received by the router. 

 

TX Packets Dropped: 

The number of packets that were dropped while being sent, due to 

errors, collisions, or router resource limitations. 

 

RX Packets Dropped: 

The number of packets that were dropped while being received, due to 

errors, collisions, or router resource limitations. 

 

Collisions: 

The number of packets that were dropped due to Ethernet collisions (two or more 

devices attempting to use an Ethernet circuit at the same time). 

 

Errors: 

The number of transmission failures that cause loss of a packet. 

 

3.4.6 Active Sessions

 

The Active Sessions page displays full details of active sessions through your router. A session is a 

conversation between a program or application on a LAN-side computer and a program or 

application on a WAN-side computer. 
 

Internal: 

The IP address and port number of the LAN-side application. 

 

Protocol: 

The communications protocol used for the conversation. 

 

External: 

The IP address and port number of the WAN-side application. 

 

NAT: 

The port number of the LAN-side application as viewed by the WAN-side application. 

 

Priority: 

The preference given to outbound packets of this conversation by the QoS logic. 

Smaller numbers represent higher priority. 

Summary of Contents for G2Wifi II
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands