3Jtech G2Wifi II Page 78 User Manual Download

Page: 78 / 87

http://www.3jtech.com.tw

http://www.pnpipcameras.com

G2wifi II User’s Manual

LAN Settings:

In this page, you can configure the IP Phone LAN port’s setting.

The LAN port’s default IP address is 192.168.123.1, Net Mask is 255.255.255.0, and DHCP Server

enabled. The start IP address if 150, end IP address is 200. It is not necessary to change the LAN

settings. You can connect your PC to the LAN port, set your PC as DHCP Client mode, then you can

get IP address from the VoIP.

When you finished the setting, please click the

Submit

button. If there is nothing need to change,

please click the

Save Change

Item in the left side, then click the

Save

button. The change you made

will save into the system and the system will reboot automatically.

Summary of Contents for G2Wifi II
























































































Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands

3Jtech G2Wifi II, User Manual

Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands