3Jtech G2Wifi II Page 54 User Manual Download

Page: 54 / 87

http://www.3jtech.com.tw

http://www.pnpipcameras.com

G2wifi II User’s Manual

3.2.13 Ping WAN

Ping WAN function provides you with an option to check the WAN connection is valid or not, if not,

the router will switch from Ethernet to the modem Dialup, or from the modem Dialup(Always on mode)

to Ethernet.

After Ping WAN is enabled, it does not doing the PING all the time, it only happens after finding that

there are data packets going out(to WAN) but none is coming in(form WAN).

Note 1:

When modem Dialup is activated, Ping WAN will take place only for "Always on mode", not for "On demand

mode".

Note 2:

When modem Dialup(Always on mode) is activated and "WAN LInk Timeout = 0", after Ping WAN confirms that

WAN connection is not ok, the modem Dialup will be disconnected and tried to connect again, it will not switch to

Ethernet.

Note 3:

The

Ping WAN packet is transmitted from current activated WAN interface to the assigned IP, such as from

Ethernet or the modem Dialup, it can not transmit from both Ethernet and the modem Dialup simultaneously, so when the

modem Dialup is activated, only after failure of Ping WAN (Always on mode), idle timeout or max connection timeout(On

demand mode), the router will switch from the modem Dialup to Ethernet.

The description of related parameter for the Ping WAN function is as follows:

Enable Ping WAN:

Enable the function of Ping WAN.

Start to Ping when:

Set up the circumstance that Ping will start to activate. Two options are

offered to allow you choosing the Ping mode. The settings are:

Always Ping:

The router will always do the ping.

After tx to WAN, find no response:

The router will do the ping if no response

is found from Ethernet WAN.

Ping repetition time(time between 2 Ping):

The time interval of sending the Ping packet.

Max Allowed Successive Lost Ping:

The maximum times that the G2wifi II allows to receive

no response from the successive Ping. The WAN connection will be transferred from

Ethernet_WAN into the modem Dialup in case it exceeds this limit.

Ping WAN IP Address:

The

IP address is used for the ping.

Summary of Contents for G2Wifi II
























































































Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands

3Jtech G2Wifi II, User Manual

Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands