manualshive.com logo in svg

3Jtech G2Wifi II, User Manual

Share
Download
3Jtech G2Wifi II User Manual Download Page 16

http://www.3jtech.com.tw

 

http://www.pnpipcameras.com

   

G2wifi II User’s Manual   

Copyright of 3JTech Co., Ltd. (also doing business as A3J Engineering Inc.) 

16 

 

 

3. Web-Based Management 

This chapter instructs you how to configure and manage the G2wifi II through the web user interface 

it supports. With this facility, you can easily access and monitor through any one LAN port of the 

G2wifi II router. 

 

After G2wifi II has been connected to your PC via RJ45 network cable, type http://192.168.8.1 in IE 

browser, it will show the following screen and ask you to input the user name and password in order 

to login and access authentication. The default user name is 

“admin”

 or

 “user”

, and the password 

is blank. With the former user name to login, the user is able to fully access and configure the system. 

As to the latter, the user merely owns the right to read the system. For the first time to use, please 

enter the default user name and keep the password blank, then click the 

Log In

 button. The setup 

page for G2wifi II will be displayed once the login process is successful. 

   

 

Summary of Contents for G2Wifi II
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands