3Jtech G2Wifi II Page 27 User Manual Download

Page: 27 / 87

http://www.3jtech.com.tw

http://www.pnpipcameras.com

G2wifi II User’s Manual

Modem Initialization String:

Enter any extra AT commands here. AT commands start

with AT. Normally you will not need to enter any.

CDMA CallerID Phone Number:

The user can wake up remotely the idle router to return

into working status with this phone number / mobile phone number you set up.

CDMA ISP Settings:

Your CDMA service provider will provide you with the values to fill in for

the

required

fields of

CDMA Dial Command

Username

Password

and

Data Service Type

CDMA Dial Command:

If your modem supports modem compatibility enter ATD*99***1#.

If your modem does not enter AT+CGDATA=1.

Data Service Type:

This sets the AT cCRM value. For

Quick-Net-Connect(QNC) and 1xRTT select the correct PPP Packet Data service.

SIM card PIN code:

SIM card password for authentication.

Summary of Contents for G2Wifi II
























































































Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands

3Jtech G2Wifi II, User Manual

Search results

Summary of Contents for G2Wifi II

Reviews:

Related manuals for G2Wifi II

Brands by name

Popular brands