manualshive.com logo in svg

3D Histech Pannoramic SCAN 150 1.18, User Manual, Page: 13 / 131

Share
Download
3D Histech Pannoramic SCAN 150 1.18 User Manual Download Page 13

Pannoramic SCAN 150 1.18 User’s Guide

1 Product Description

1  Product Description

1.1  Product Overview

1.1.1  Intended Use

The Pannoramic SCAN 150 is designed to use transmitted light and reflected light fluorescence to 
digitize biological samples and specimens (histological sections, typically). The target users of the 

product can work for example, in education, research, industrial, or medical sectors.

  Warning!

 

After each scanning make sure to inspect the digital slide for over-exposed 
areas. If the slide is scanned based on improperly set parameters, it can 

highly affect the diagnostic result because of information loss.

  Warning!

Any modification to a hardware or software component of the PC will 

highly affect the functionality of the scanner program.

1.1.2  Features and Benefits

The Pannoramic SCAN 150 offers world class brightfield and fluorescent whole slide scanning on up 
to 9 channels. An outstanding 0.12 µm/pixel (in Brightfield) and 0.16 µm/pixel (in Fluorescent) 

resolution is achieved with the 40×/NA 0.95 (equivalent to 80× magnification in BF and 62× 
magnification in FL) Carl Zeiss Plan-Apochromat objective.

Key features of the Pannoramic SCAN 150 Scanner are:

•

Up to 9 freely selectable color filters for fluorescence

•

High-end fluorescent illumination device – Lumencor Spectra 6 Light Engine

•

Multiband filter support

•

FL scanning with a low noise, 16-bit scientific CMOS pco.edge 4.2 camera

April 3, 2014 - Rev. 1

3DHISTECH Ltd.

13(131)

Summary of Contents for Pannoramic SCAN 150 1.18




































































































































Reviews:

No comments