manualshive.com logo in svg

3D Histech Pannoramic SCAN 150 1.18, User Manual, Page: 10 / 131

Share
Download
3D Histech Pannoramic SCAN 150 1.18 User Manual Download Page 10

Pannoramic SCAN 150 1.18 User’s Guide

Notes Regarding Operational Safety

  Disconnect plug!

Remember to unplug the power cord before you open the Pannoramic SCAN 
150 or replace a fuse!

  Warning!

Only connect external devices that are safety extra low voltage rated to the 
instrument to avoid the risk of electrical shock.

  Warning!

Pannoramic SCAN 150 does not include any special facilities to protect from 
samples with an etching, potentially infectious, toxic, radioactive or other 
health-damaging effect. You are under obligation to comply with all currently 
binding legislation, notably, national accident prevention rules when handling 
samples of this kind.

  Caution!

Dirt or dust may adversely impact the operating capability of the Pannoramic 
SCAN 150. For this reason, measures must be taken to eliminate such influences
to a maximum possible degree. During periods of non-use, the Pannoramic 
SCAN 150 must be protected with a dust cover. Check that power is turned off 
before you put the cover on.

  Caution!

Avoid touching the lamp bulb. Disconnect power and let the lamp cool down for
about 15 minutes before replacing the lamp.

  Crush hazard!

There is crush hazard in the movement area of the slide insert during operation.
Please note that the digitizing process has to be interrupted and the insert 
moved via software to the output position before removing the insert.

  Warning!

A defective Pannoramic SCAN 150 is not classified as domestic waste. It must be
properly disposed in accordance with currently valid legal requirements.

  Warning!

The Pannoramic SCAN 150 may not be operated by other than properly 
instructed persons. Operating personnel must be fully aware of the potential 
dangers which a particular field of application involves. The Pannoramic SCAN 
150 is a precision instrument which may suffer a significant reduction in 
operational functions or even physical destruction following intervention 
performed in any nonconforming manner.

  Warning!

If an HXP 120 illumination unit is used, the corresponding warnings included in 
the manufacturer’s operating manual have to be observed.

April 3, 2014 - Rev. 1

3DHISTECH Ltd.

10(131)

Summary of Contents for Pannoramic SCAN 150 1.18




































































































































Reviews:

No comments