manualshive.com logo in svg

3D Histech Pannoramic SCAN 150 1.18, User Manual, Page: 119 / 131

Share
Download
3D Histech Pannoramic SCAN 150 1.18 User Manual Download Page 119

Pannoramic SCAN 150 1.18 User’s Guide

5 Troubleshooting and Maintenance

  Caution!

Incorrect handling may considerably reduce the lamp

 

module’s useful 

life. Hold it by the ceramic part in all cases! Never touch the lamp’s 

glass surface or the inside surface of the reflector. Skin oil is harmful to 
these parts.

7. Tighten pressure bolt again with the lever (

Figure 79 – 1

).

8. Re-establish plug-in connection.

9. Screw the lateral cover-plate down to the housing.

10. Connect power plug.

11. Set hour meter (time counter) to zero.

5.3.4  Removing a slide

If a slide got jammed or has suffered breakage during the process of digitization, stop the process 

and, if possible, move the slide holder to a position where the slide can be easily removed by clicking 
the 

Emergency Manual Slide Removal Position

 button (see section 

4.3.6 Service panel

).

  Warning! 

Crush hazard! Before you remove a jammed slide, cancel

 

the running 

digitization process, terminate the software session and turn the power

off.

  Caution!

Any manipulation performed on a mechanical component must be 
followed by a complete device initialization routine (software restart).

April 3, 2014 - Rev. 1

3DHISTECH Ltd.

119(131)

Summary of Contents for Pannoramic SCAN 150 1.18




































































































































Reviews:

No comments