manualshive.com logo in svg

3D Histech Pannoramic SCAN 150 1.18, User Manual, Page: 111 / 131

Share
Download
3D Histech Pannoramic SCAN 150 1.18 User Manual Download Page 111

Pannoramic SCAN 150 1.18 User’s Guide

5 Troubleshooting and Maintenance

4. Remove magazine manually (see section 

5.3.6 Removing the Magazine from the 

Transporting System

). If a jammed magazine cannot be removed, contact service 

personnel.

5. Reattach protective covers.

6. Reconnect 24V power supply and control computer to line power supply.

7. Switch on the 24 V power supply.

8. Switch on the control computer.

9. Launch control software.

Illumination error! Probably the lamp has burned out. Please turn off the scanner and check the 
lamp!

•

Halogen lamp is defective

•

Replace the halogen lamp (see section 

5.3.2 Replacing the 

 

 halogen lamp

).

Image is black

•

Halogen lamp is defective

•

Replace the halogen lamp (see section 

5.3.2 Replacing the 

 

 halogen lamp

).

Virtual slide is improperly focused almost across its entire surface

•

Focus range enabled

•

Disable 

Limiting focus range

.

Poor image quality

•

Imaging error (for example, chromatic aberrations)

•

Contact 3DHISTECH Service for support.

  Warning!

Do not modify the camera driver settings, as the default factory 

settings give the most accurate images.

April 3, 2014 - Rev. 1

3DHISTECH Ltd.

111(131)

Summary of Contents for Pannoramic SCAN 150 1.18




































































































































Reviews:

No comments