manualshive.com logo in svg

3D Histech Pannoramic SCAN 150 1.18, User Manual, Page: 122 / 131

Share
Download
3D Histech Pannoramic SCAN 150 1.18 User Manual Download Page 122

Pannoramic SCAN 150 1.18 User’s Guide

5 Troubleshooting and Maintenance

2. Pull protective cover halves apart or remove the right part completely (see section 

5.3.1 

Removing the protective covers

).

3. Select the desired filter in the corresponding software window (see section 

4.2.3 

Microscope Settings / Filter Settings

). The filter will be positioned in such a way that the 

user can access it without having to turn the filter wheel manually.

4. Enter the respective parameters in the input fields.

  Warning!

Crush hazard! Rotating the filter turret motorically during installation 
or removal may lead to injury.

5. Hold the filter module 

(3)

 by its handling pads (one on the right, one on the left (lateral) 

side of the module) and insert it in forward tilted position from above into the upper spring-

loaded clamps 

(1)

 at the filter wheel.

6. Press the filter module down, until it safely connects to the bottom spring-loaded clamps 

(2)

 of the filter wheel.  Mounting position of the filters: excitation filter 

(5)

; emission filter 

(4)

.

7. To remove the filter module, first slightly tilt it out of its upper spring-loaded fixtures, then 

pull it out of the bottom spring-loaded components and take it off.

8. Place the protective covers back again (see 

5.3.1 Removing the protective covers

).

9. If an HXP 120 illumination unit is used, turn it on again (consider the cooling time possibly 

required).

April 3, 2014 - Rev. 1

3DHISTECH Ltd.

122(131)

Summary of Contents for Pannoramic SCAN 150 1.18




































































































































Reviews:

No comments