manualshive.com logo in svg

3D Histech Pannoramic SCAN 150 1.18, User Manual, Page: 121 / 131

Share
Download
3D Histech Pannoramic SCAN 150 1.18 User Manual Download Page 121

Pannoramic SCAN 150 1.18 User’s Guide

5 Troubleshooting and Maintenance

  Caution!

If the slide is broken, make sure to remove all pieces completely from 
the device. The edge of the broken area of the slide is sharp and it can lead 

to injury and contagion! Broken slide can be removed only by a well-trained
person!

7. Release clamping lever 

(4)

 and turn down the slide loader 

(2)

 back into the original position 

and pull it inwardly, until the guiding pin connects with the motor block groove again.

8. Press the slide loader down to mechanical stop position, in which the locking lever must 

engage 

(1)

. Use moderate force to press the loader part opposite the motor in clamp 

direction 

(2)

, until this part mechanically engages, too.

9. Close the protective cover again (see section 

5.3.1 Removing the protective covers

).

10. Launch the control software.

5.3.5  Installing and Removing the Filter Module (Fluorescent Option)

Figure 83 – Installing and removing the filter module

1. If using an HXP 120 illumination unit, turn it off.

  Warning!

Crush hazard! Stop the running digitization process before you proceed

with filter module installation or removal.

April 3, 2014 - Rev. 1

3DHISTECH Ltd.

121(131)

Summary of Contents for Pannoramic SCAN 150 1.18




































































































































Reviews:

No comments