manualshive.com logo in svg

2N Netstar, Manual

Share
Download
2N Netstar Manual Download Page 46

46

Incoming parameters (phone is dialling)

Call type

 – determines the preferred type of communication on this port. Choose

one of the 

, 

, 

 and 

 options.

Voice FAX A3.1kHz Audio

56kb Modem

DTMF dial enabled

 – check this item to make the carrier detect DTMF dialling

from an analogue phone.

Pulse  dial  enabled

  –  check  this  item  to  make  the  carrier  detect  pulse  dialling

from an analogue phone.

FLASH  length  [ms]

  –  the  parameter  sets  the  maximum  time  of  the  FLASH

signal  transmitted  from  a  local  phone  to  the  PBX.  The  default  value  is  150  ms
and the minimum value is 80 ms.

Disable  port  DTMF  detection

  –  use  this  parameter  to  disable/enable  DTMF

detection  using  a  detector  on  the  board  in  order  to  save  the  internal  PBX
detectors.

Outgoing parameters (phone is ringing)

CLI  broadcasting  mode

  –  the  parameter  defines  the  preferred  CLIP  (Calling

Line  Identification  Presentation)  transmission  type.  The  selections  are 

, 

DTMF

 and 

.

FSK

none

Summary of Contents for Netstar



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands