manualshive.com logo in svg

2N Netstar, Manual

Share
Download
2N Netstar Manual Download Page 124

124

6.9 Ring Tones

To  set  the  ringing  tones  use  the 

  menu.  Each  ringing

Global  Data  –  Ring  Patterns

tone consists of a ring pattern and Cornet tune. Some terminals are unable to change
the ring tune and use the ring pattern only. See a list of available ring patterns on the
left. You can add, remove or rename the ring patterns using the context menu. During
database  creation,  default  progress  tone  patterns  are  created  that  can  be  edited  or
removed  as  necessary.  To  restore  the  default  settings  without  removing  the  tones
created by you, use the 

 option. To restore the default settings and remove all

Update

the ring tones, use the 

 option in the context menu. To create the ring tones,

Default

use the following parameters:

Figure: 

View of Ring Tone Configuration Menu

Repeat

  –  check  this  option  to  make  a  tone  pattern  being  played  repeatedly.  If

this option is not checked, the tone pattern is used only once.

Cornet tune

 – use this parameter to assign a ring tone tune to a selected ring

pattern in the StarPoint key telephones.

BRI  signal

  –  use  this  parameter  to  set  the  ring  tone  signalling  for  the  ISDN

terminals that support multi–tune ringing.

Delay

 – here set the ring pattern using two columns and four rows. Set the 

ON

and 

 columns for each row to be used. 

 represents the ring current time

OFF

ON

and 

  represents  the  row  resumption  delay.  Both  the  parameters  are  set  in

OFF

milliseconds.

Summary of Contents for Netstar



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands