manualshive.com logo in svg

2N Netstar, Manual

Share
Download
2N Netstar Manual Download Page 171

171

Alerting strategy

This  strategy  represents  a  new  DISA  concept.  When  a  call  comes  to  the  port,  it  is
immediately  routed  to  the  preset  Alerting  destination  and  this  destination  is  being
alerted till the end of timeout. The timeout is set by the 

 parameter. The call

Timeout

is not answered during the timeout and the calling user hears the alert tone from the
network. After the timeout, the call is answered, but only towards the calling user, who
is played the predefined progress tone. The Alerting destination is still being alerted. If
the  DTMF  option  is  checked,  the  DTMF  detector  is  connected  after  the  timeout  and
remains  active  until  the  end  of  routing  (answer,  reject,  etc.).  The  DTMF  digits  are
transferred into the router selected in the 

 option.

Destination after DTMF dial

 

 

Figure: 

Příklad konfigurace objektu DISA se strategií Vyzváněcí

The menu consists of the following parameters:

Alerting destinace

 – set the alerting destination parameters.

Type

 – set the destination type for call routing.

Id

 – choose a destination of the selected type.

Timeout [s]

 – set the timeout for playing the predefined voice message.

The  '0'  selection  is  not  suitable  for  the 

  strategy  since  the  call

Alerting

would be answered immediately, which is undesirable in this strategy.

Tone

 – select a tone from the current list of PBX progress tones.

Destination  after  DTMF  dial

  –  set  a  router  for  call  routing  by  the  PBX  after

DTMF dialling.

DTMF

 – define whether or not the DTMF detector shall be allocated for this

DISA object.

Type

 – set the router type for call routing.

Summary of Contents for Netstar



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands