Zte ZXR10 5900E Series Скачать руководство пользователя страница 13

Страница: 13 / 226

Chapter 1 IPv6 Address Configuration

Each IPv6 packet can have 0, 1 or more extension headers. Each extension header

is determined by the "next header" domain of the previous header.

Address Classifications

RFC

2373, addresses are classified based on the address prefix. For a list of IPv6

address types, refer to

Table 1-1

Table 1-1 IPv6 Address Types

Address Type

Prefix (Binary)

Unassigned addresses

00...0(128 bits)[::/128]

Loopback addresses

00...1(128 bits )[::1/128]

Multicast addresses

11111111[FF00::/8]

Link-local unicast addresses

1111111010[FE80::/10]

Global unicast addresses

Others

The broadcast address in IPv6 is not valid any more. RFC2373 defines three types of IPv6

address:

Unicast

It is the identifier of a single interface. The packets sent to a unicast address will be

transmitted to the interface with this address identifier.

Multicast

It is the identifier of a group of interfaces. These interfaces belong to different nodes.

The packets sent to a multicast address will be transmitted to all the interfaces with

this address identifier.

Anycast

It is the identifier of a group of interfaces. These interfaces belong to different nodes.

The packets sent to an anycast address will be transmitted to an interface with this

address identifier (selecting the nearest one by calculating the distance based on

routing protocol).

An IPv6 unicast address can be regarded as an entity with two fields. One field is used

to identify networks and the other is used to identify interfaces of nodes on this network.

In the subsequent description of the specific unicast address types, the user will find that

the network identifier can be divided into several parts, each of which identifies different

network part.

Unicast address

An IPv6 unicast address can have a varied-length prefix. For the structure of the IPv6

unicast address, refer to

Figure 1-3

1-3

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды