Zte ZXR10 5900E Series Скачать руководство пользователя страница 188

Страница: 188 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

matched tunnel entity according to the source address and destination address of

the packet. If the matched tunnel entity is found, the IPv4 header encapsulated is

removed, and the left IPv6 packet is handled according to the IPv6 packet receiving

flow.

ISATAP tunnel principle is shown in

Figure 16-1

Figure 16-1 ISATAP Tunnel Principle

16.2 Configuring an ISATAP Tunnel

To configure an ISATAP tunnel on ZXR10 5900E, perform the following steps:

Step

Command

Function

ZXR10(config)#

interface v6_tunnel1

tunnel_no

Creates an IPv6 tunnel

interface. Use the

format

of this command to delete a

tunnel interface.

ZXR10(config-if)#

ipv6 enable

Enables IPv6.

ZXR10(config-if)#

ipv6 address

addrprefix / prefix-len

eui-64

Configures an eui-64 address

on an interface for an ISATAP

tunnel.

ZXR10(config)#

ipv6-tunnel-config

Enters IPv6 tunnel

configuration mode.

ZXR10(config)#

interface v6_tunnel1

tunnel_no

Enters IPv6 tunnel interface

configuration mode.

ZXR10(config-ipv6-tunnel-if-v6_tunnel1)#

tunnel

mode ipv6ip isatap

Sets the tunnel mode to isatap.

Use the

format of this

command to delete the current

tunnel mode.

16-2

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды