Zte ZXR10 5900E Series Скачать руководство пользователя страница 103

Страница: 103 / 226

Chapter 8 IS-ISv6 Configuration

Parameter

Description

interval

Specifies the interval in the unit of seconds. The value range

is 1-120. The default value is 10 seconds.

level-1

level-2

Specifies the level of the topology computation interval.

For a description of the parameters in Step 2.10, refer to the following table:

Parameter

Description

encrypt

key

Specifies the encrypted key, which is a string of 24 to 140

characters.

key

Specifies the plaintext key, which is a string of 1 to 100

characters.

level-1

level-2

Specifies the authentication range. The default value is

level-1-2.

After configuring this command, you also need to set the same authentication code for

SNP packets. By default, application also applies to SNP packets. To clear SNP packet

authentication, run the command

disable-snp-authentication

For a description of the parameters in Step 2.13, refer to the following table:

Parameter

Description

number

Specifies the number of parallel routes supported. The value

range is 1-32.

If the maximum-paths parameter is not specified, only one parallel route is supported by

default.

For a description of the parameters in Step 2.14, refer to the following table:

Parameter

Description

size

Specifies the size of LSP packets in the unit of bytes. The

value range is 512-7680.

By default, the size of LSP packets transmitted on a broadcast link is 1,497 bytes. You

can run this command to specify the LSP packet size to a value between 512 and 7,680

bytes. It is not recommended that users run this command unless really necessary.

For a description of the parameters in Step 2.15, refer to the following table:

Parameter

Description

with-original-metric

Using original metric of the interface.

8-7

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды