Zte ZXR10 5900E Series Скачать руководство пользователя страница 150

Страница: 150 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

12.2 Configuring MLD

To configure MLD on the ZXR10 5900E, perform the following steps:

Step

Command

Function

ZXR10(config-mcast-ipv6)#

router mld

ZXR10(config-mcast-ipv6)#

no router mld

Enters MLD mode. This is

not related to whether MLD

is enabled. That whether

MLD is enabled id controlled

by IPv6 multicast-routing.

Use the

format of this

command to delete all MLD

configuration and restore the

default configuration.

ZXR10(config-mcast-mld-ipv6)#

interface

interface_name

ZXR10(config-mcast-mld-ipv6)#

no interface

interface_name

Enters MLD interface

configuration mode. This

is not related to whether MLD

is enabled on an interface.

That whether MLD is enabled

on an interface is controlled by

whether PIM is enabled on an

interface. Use the

format

of this command to delete

the interface configuration

and restore the default

configuration.

ZXR10(config-mcast-mld-ipv6)#

ssm-map static

access-list-number

default

source-address

Configures mapping from

groups in a specified range to

the source.

ZXR10(config-mcast-mld-ipv6)#

require-alert-options

Discards the

MLD

packets

without carrying the

Router_Alert_Options option in

IPv6 headers.

To restore the default setting,

run the

form of this

command.

For a description of the parameters in Step 2, refer to the following table:

Parameter

Description

intf-name

Interface name

For a description of the parameters in Step 3, refer to the following table:

12-2

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды