Zte ZXR10 5900E Series Скачать руководство пользователя страница 78

Страница: 78 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

OSPFv3 Principle

Compared with OSPFv2, OSPFv3 has almost the same working mechanism but has also

revised OSPFv2 so as to support the IPv6 address format. The following sections describe

in detail the similarities and differences between OSPFv2 and OSPFv3. For details about

the OSPFv2 principles, please refer to "OSPF Configuration" in IPv4 Routing Volume.

Similarities Between OSPFv3 and OSPFv2

OSPFv3 has almost the same protocol design concept and working mechanism as

OSPFv2.

The same packet types: Hello, DD, Link State Packet (

LSP

), Link State Update (

LSU

LSAck packets.

The same area division.

The same LSA flooding and synchronization mechanisms:

To guarantee the

correctness of Link-state Database (

LSDB

) information, the reliable flooding and

synchronization of LSAs must be guaranteed.

The same route computation method: Both use the Shortest Path First (

SPF

)

algorithm to compute routes.

The same network types: Both support four network types, i.e. broadcast, NBMA,

point-to-point, point-to-multipoint.

The same neighbor discovery and neighbor establishment mechanisms: After an

OSPF router is started, it sends a Hello packet via the OSPF interface to another

OSPF router. Upon receipt of the Hello packet, the latter OSPF router checks the

parameters defined in the packet. If the parameters in the received packet are the

same as those in its own packet, adjacency is established between the two routers.

Two routers in an adjacency relationship do not necessarily become neighbors. This

depends on the network type. The two routers become real neighbors only when

they have successfully exchanged the DD packet and the LSA and their LSDBs are

synchronized with each other.

The same DR election mechanism: The DR and BDR need to be elected in NBMA

and broadcast networks.

Differences Between OSPFv3 and OSPFv2

There are differences between OSPFv3 and OSPFv2 because OSPFv3 is based on IPv6.

The topology of OSPFv3 is link-based whereas that of OSPFv2 is subnet-based.

IPv6 uses the term "link" to describe the facilities or mediums used by nodes for

communications over the link layer. Nodes are connected with links. Multiple IP

subnets can be attached to the same link. Two nodes in different IP subnets can

communicate with each other directly over a single link.

Address semanteme is deleted from OSPFv3.

The OSPFv3 packet contains no IPv6 address except for the LSA payload carried in

a link state update packet. The router LSA and network LSA do not contain network

addresses but only indicate topology information. The OSPF router ID and the LSA

ID are reserved as 32-bit IPv4 addresses and not assigned with any IPv6 address.

7-2

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды