Zte ZXR10 5900E Series Скачать руководство пользователя страница 24

Страница: 24 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

Command

Function

ZXR10#

show ipv6 interface

interface-name

Shows details about the specified

IPv6 interface.

ZXR10#

show ipv6 interface brief

interface-name

Shows the brief information about

the specified IPv6 address.

The following is sample output from the

show ipv6 interface

interface-name

> command:

ZXR10(config)#show ipv6 interface vlan10

Interface vlan10 is up, line protocol is up

IPv6 is enabled,

Hardware is Vlan

HWaddr: 0022.935a.f750

index 151

Bandwidth 1000000 Kbits

IPv6 MTU is 1500 bytes

inet6 fe80::222:93ff:fe5a:f750/64

inet6 1000::2/64

DAD attemps number:3

ND reachable-time is 30000 milliseconds

ZXR10(config)#show ipv6 interface brief

vlan2

[up/down]

fe80::200:22ff:fe22:0

[tentative]

15::2/64

[tentative]

vlan10

[up/up]

fe80::222:93ff:fe5a:f750

1000::2/64

ZXR10(config)#

For a description of the sample output from the

show ipv6 interface

interface-name

command, refer to the following table:

Command Output

Description

IPv6 is enable

Indicates that IPv6 is enabled on the interface.

Hardware is Vlan

Indicates that the interface is an VLAN interface.

HWaddr

Indicates the physical address.

index

Indicates the interface index.

Bandwidth

Indicates the bandwidth.

[tentative]/[duplicated]

Indicates the IPv6 address status.

[disable/down]

[disable/down] indicates that IPv6 is disabled and the

interface protocol is down; [up/down] indicates that IPv6 is

enabled and the interface protocol is down.

1-14

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды