Zte ZXR10 5900E Series Скачать руководство пользователя страница 86

Страница: 86 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

Parameter

Description

dead-interval

seconds

Specifies the dead interval of neighbors on the virtual link in

the unit of seconds. The value range is 1-8192. The default

value is 40 seconds.

retransmit-interval

seconds

Specifies the retransmission interval of packets on the virtual

link in the unit of seconds. The value range is 1-8192. The

default value is 5 seconds.

transmit-delay

seconds

Specifies the delay after which a link state update packet

is transmitted on the virtual link in the unit of seconds. The

value range is 1-8192. The default value is 1 second.

The command parameter in step 8 is described as follows:

Parameter

Description

metric-value

Default metric of external routes, in the range of 1-16777214.

The command parameters in step 9 are described as follows:

Parameter

Description

access-list-name

The first character can be a digit. Use an unused name.

name of a route-map

Route-map template name

In: The template specified is used to filter routes.

The command parameter in step 10 is described as follows:

Parameter

Description

number

Maximum number of routes for load sharing in OSPF, in the

range of 1-32, with the default value of 1.

The command parameter in step 11 is described as follows:

Parameter

Description

interface-name

Interface name

The command parameters in step 12 are described as follows:

Parameter

Description

protocol

Specifies the name of the redistributed protocol, such as

"connected", "static", "RIP", "BGP", "ISIS" or "OSPF".

metric-value

Specifies the metric of the redistributed LSA. By default, the

default-metric of the instance is used. The value range is

0-16777214.

7-10

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Содержание ZXR10 5900E Series



































































































































































































































Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды

Zte ZXR10 5900E Series, Руководство по настройке

Результаты поиска

Содержание ZXR10 5900E Series

Отзывы:

Похожие инструкции для ZXR10 5900E Series

Бренды по названию

Популярные бренды