4
. 3).AE5..
–.medium.dustiness
.
AE6..
–.strong.dustiness
. 4).AF2..
–..occurrence.of.corrosive.or.polluting.substances.from.atmosphere..Presence.of.corrosive.polluting.
substances.is.significant.
. 5).AG2..
–.medium.mechanical.stress.by.impacts.–.common.industrial.processes
. 6).AH2..
–.medium.mechanical.stress.by.vibrations.–.common.industrial.processes
. 7).AK2.
–.serious.risk.of.growth.of.vegetation.and.moulds
. 8).AL2.
–.serious.danger.of.the.occurance.of.animals.
(insects, birds, small animals)
. 9).AM-2-2. –.normal.level.of.the.signal.voltage..No.additional.requirements
10).AN2.
–.medium.solar.radiation.with.intensities.>.500.W/m
2
.and.≤.700.W/m
2
11).AP3.
–.medium.seismic.effects;.acceleration.>.300.Gal.≤.600.Gal
12).BA4.
–.personal.abilities..Instructed.people.
13).BC3.
–..frequent. contact. with. the. earth. potential.. Persons. coming. frequently. into. contat. with. “live”. parts. or.
standing.on.a.conducting.base.
Actuator.are.not.intended.for.use.in.residential.environments.and.may.not.secure.an.adequate.protection.of.receiving.
a.radio.signal.in.these.environments.
.
Operating position
The.actuators.can.be.operated.in.any.operating.position.
3. OPERATION MODE, SERVICE LIFE OF ACTUATORS
Operation mode
The.actuators.can.be.operated.with.the.type.of.loading.S2.according.to.ČSN.EN.60.034-1..The.run.period.at.temperature.
+50.°C.is.10.minutes;.the.mean.value.of.loading.torque.should.not.exceed.60.%.of.the.value.of.maximum.tripping.torque.Mv..
The.actuators.can.also.work.in.the.regime.S4.
(interrupted run with start-up)
.according.to.ČSN.EN.60.034-1..Load.factor..
N/N+R. is. max.. 25. %;. the. longest. working. cycle.
(N+R)
. is. 10. minutes.
(course of working cycle is shown in the figure).
..
The.highest.number.of.closing.operations.in.automatic.regulation.is.1200.cycles.per.hour..Mean.value.of.loading.torque.with.
load.factor.25.%.and.surrounding.tempe50.°C.is.not.higher.than.40.%.of.maximum.tripping.torque.Mv..
The.highest.mean.value.of.loading.torque.is.equal.to.rated.torque.of.the.actuator.
Corrosion protection
Actuators.are.standardly.delivered.with.surface.treatment.corresponding.to.category.of.corrosion.aggressiveness.
C1,.C2.and.C3.according.to.ČSN.EN.ISO.12944-2..
On.customer's.request.is.possible.to.do.surface.treatment.correcponding.to.category.of.corrosion.aggressiveness.
C4,.C5-I.and.C5-M.
In.following.table.is.provided.and.overview.of.environment.for.each.categories.of.corrosion.aggressiveness.accor-
ding.to.ČSN.EN.ISO.12944-2.
Corrosion
aggressiveness
level
Example of typical environment
Outdoor
Indoor
C1.
.
Heated.buildings.with.clean.atmosphere..
.
(very.low)..
.
e.g..offices,.shops,.schools,.hotels.
C2.
Atmosphere.with.low.level.of.pollution..
Unheated.buildings,.in.which.may.occur.
.
(low)..
Mostly.outdoor.areas..
condensation,.e.g..stocks,.sports.halls.
.
C3.
Urban.industrial.atmospheres,.
Production.areas.with.high.humidity.and.low.air.
.
(middle).
mild.pollution.of.sulfur.dioxide..
pollution,.e.g..food.industry,.processing..
.
.
Seaside.areas.with.middle.salinity...
factories,.breweries.
.
C4.
Industrial.areas.and.seaside.areas..
Chemical.plants,.swimming.pools,..
.
(high).
with.middle.salinity..
seaside.shipyard.
C5-I
(very.high..
Industrial.areas.with.high.humidity.
Buildings.or.areas.with.predominantly.continuous.
.
–.industrial).
and.aggressive.atmosphere..
condensation.and.high.air.pollution...
C5-M..
.
(very.high.
Seaside.areas.with.high.salinity..
Buildings.or.areas.with.predominantly.
.
–.seaside).
.
continuous.condensation.and.high.air.pollution.
