background image

Zlin Aviation 

 

Section 1  

Maintenance Manual                                        Aircraft Maintenance Manual

 

Issued: 01/02/2006 

       

 

     QAP-AMM-Rev02 

Date of latest Revision: 23/01/2013                                            

 Page Number: 1-8 

 

 
 

Coolant 

See engine operators manual 
 
In use of conventional coolant: 

Coolant temperature:(coolant exit temperature) 

Max.....................................................................120°C (248°F) 
 

Cylinder head temperature: 

Max......................................................................135° (275°F) 
Permanent monitoring of coolant temperature and cylinder head temperature is necessary. 
 
In use of waterless coolant: 

Cylinder head temperature: 

Max.......................................................................135°C (275°F) 
Permanent monitoring of cylinder head temperature is necessary. 
 

Engine start, operating temperature: 

Max........................................................................50°C...........(120°F) 
Min.........................................................................-25°C..........(-13°F) 
 

Fuel pressure 

Max........................................................................0,4bar..........(5,8 psi) 
Min.........................................................................0,15bar........(2,2 psi) 

Warning

: exceeding the max admissible fuel pressure will over-ride the float valve of the carburators and to 

engine failure. 
 
 
 

FUEL 

 
Approved Fuel Grade: 92 Unleaded Automobile Fuel, “Auto gas” (Yellow) 
Approved 

Alternate 

Fuel Grade: 100LL Aviation Fuel, “Avgas” (Blue) 

 

CAUTION:  

100LL Avgas is only to be used as an 

alternate fuel type 

if 92 octane unleaded auto fuel is not available. 

Due to the high lead content, the use of 100LL Avgas is restricted to less than 30% of engine time. See the 
latest Rotax engine operational supplement for more detailed fuel specifications and information. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Savage Classic



































































































Отзывы: