background image

 

ZP1-F Series Operation Manual 

Audible indicators 

The control panel buzzer acts as an audible indicator to highlight system events. 
It can sound a continuous tone or an intermittent tone. 

Table 6: Audible indications 

Indication 

Description 

The control panel buzzer sounds 
continuously 

Indicates a fire alarm or a system fault 

The control panel buzzer sounds 
intermittently 

Indicates all other faults 

 

Summary of status indications 

This section includes a summary of the default control panel status indications. 

Standby (normal status) 

Standby, or normal status, is indicated as follows: 

•  Supply LED: On steady. 

•  Sounder or Evacuation Delay LED: On steady if a sounder or evacuation 

delay was enabled. 

•  Fire Routing or Warning Delay LED: On steady if a fire routing or warning 

delay was enabled. 

•  Control panel buzzer: Off. 

Fire alarm 

Fire alarm status is indicated as follows: 

•  General Fire Alarm LEDs: Flashing if the alarm was activated by a detector. 

Steady if the alarm was activated by a manual call point. 

•  Zone LED: Flashing red if the alarm was activated by a detector. Steady red if 

the alarm was activated by a manual call point. Shows which zones are in 
alarm. 

•  Sounder Delay LED: On steady if a sounder delay was enabled. Flashing 

while the delay is active (counting down). On steady when the sounders are 
active (sounding). 

•  Fire Routing Delay LED: Flashing slow when a fire routing delay is active 

(counting). Flashing fast when an extended fire routing delay is active 
(counting). 

•  Fire Routing ON/ACKd LED: Flashing when fire routing is activated. On 

steady when the fire routing signal has been acknowledged by the remote 
monitoring equipment. 

•  Control panel buzzer: Sounding continuous. 

Содержание zp1-f Series





























Отзывы: